Acremonium: The Wet-Ceiling Genus That Rides With Stachybotrys
Quebec's INSPQ describes Acremonium as a genus of very wet places — water activity 0.90 to 0.98, a frequent companion of Stachybotrys, a coloniser of HVAC fibreglass insulation, cooling coils, drain pans, window seals, and humidifier water — that is mostly saprophytic and non-pathogenic, reported as allergenic at low prevalence, the named cause of a few humidifier hypersensitivity pneumonitis cases, a producer of livestock toxins with no human mycotoxicosis case yet reported, and an infrequent but real opportunist whose disseminated infections sit almost exclusively in the immunocompromised.
Education only — not medical advice. The health section below attributes every statement to its source — Quebec’s INSPQ (the Institut national de santé publique du Québec), whose Acremonium spp. fact sheet is this brief’s backbone, with the US CDC’s general mold framing where marked. This page does not diagnose anyone. If you believe an exposure made you sick, see a doctor.
What it is
Acremonium is a large, unsettled genus of filamentous fungi — formerly known as Cephalosporium, a name that still follows it through the allergy-testing catalogues. The INSPQ records the taxonomy in motion: depending on the author, the genus holds between 20 and 200 recognised named species, and the International Mycological Association’s database carries 205 registered strains, 197 of them named species. It sits in the order Hypocreales, family Hypocreaceae, among the Ascomycota, though it has no known sexual state and belongs in practice to the Fungi Imperfecti. Its spores are wet spores, released in small drops of slime and dispersed by insects, water droplets, or wind — a dispersal style with a consequence the INSPQ states plainly: because the conidia are bound in slime, aerosolisation is limited, air counts run low, and the genus is usually present in small concentrations in outdoor air and among the less prevalent genera in air samples. A fungus whose signature is easy to miss in the air precisely because it travels wet. Colonies in the laboratory mature within about five days, compact and at first moist and glabrous, then felt-like and powdery, in white, pale grey, pink, rose, or orange.
Where it grows
The INSPQ’s growth requirement is the brief in one line: Acremonium requires very wet conditions — building materials with high water affinity, at a water activity of 0.90 to 0.98. That is tertiary-coloniser water, Stachybotrys water, and the INSPQ says the two travel together: it is often seen growing in combination with Stachybotrys, and often reported associated with contamination by Stachybotrys chartarum, both favoured by the same very wet circumstances. Most species do not grow at 37 degrees Celsius — a fact that shapes its whole infection record below. Outdoors it is worldwide in soil, on dead plant material, in hay and rotting mushrooms, and in some foodstuffs; spore levels run higher in rural than urban environments, and it turns up in cow barns, farm houses, swineries, and grain mills at low shares of total isolates. Indoors, its record is a wet-systems inventory: it grows on acoustic and thermal fibreglass insulation used in heating, ventilation, and air-conditioning systems, and because of its high water affinity it is isolated from cooling coils, drain pans, window seals, and water from humidifiers. The crawl-space record is the strongest indoor number in the sheet: in the Finnish study the INSPQ cites, Acremonium appeared in a majority of dwellings at a mean indoor concentration of 160 CFU/m3 — but in contaminated crawl spaces at a mean of 2,240 CFU/m3, a clear link, in the authors’ reading, between crawl-space contamination and the indoor air above it (the underfloor mechanism our vented crawl spaces curation walks through). On wet gypsum wallboard in a controlled study, it appeared three weeks after immersion, among the early colonisers alongside Cladosporium and Penicillium — a finding the page carries alongside, not instead of, its tertiary association: on soaked wallboard it can arrive early; in a building’s wettest materials it keeps Stachybotrys company. One school-remediation follow-up found it in air and materials before and shortly after remediation — and not after three years, a small, dated proof that drying a building out eventually dries this genus out.
Where people encounter it
Wherever water stands inside a system: cooling coils and drain pans, humidifiers, HVAC insulation, window seals, crawl spaces, and materials that have been wet for a long time — in the INSPQ’s lists. In a gym, that translates without strain and without invention: the air handler serving the locker rooms, the drain pan under the coil, the humidifier, and any fibreglass duct liner downstream of a leak are this organism’s published habitat class. No Gym Watch location page currently names Acremonium from a location-specific test record; this brief does not invent one. What it does is pre-read the name: a laboratory reporting Acremonium on a building sample has named a genus that, on the agency’s own numbers, needed the material at a water activity of 0.90 or better — the finding is the wetness, documented by one of its most demanding tenants.
What INSPQ publishes about health effects
- The genus-level verdict, first. The INSPQ describes the many species of Acremonium as mostly saprophytic and non pathogenic, with certain species pathogenic to plants and humans. Both halves are the record; this page prints neither without the other.
- Irritation and inflammation. No specific irritation or inflammation symptoms have been attributed specifically to Acremonium spp. Substances common to most moulds, such as glucans, may cause irritation; no particular substance has been reported in relation to this genus. The column is printed as the agency prints it: empty at species level.
- Allergy. Some species have been reported to be allergenic and linked to Type I allergies (hay fever and asthma). The aerobiological surveys that detect it indoors report a low prevalence, from 4.6 percent to slightly above 10 percent, and the fungus rarely appears in large quantities — so, in the INSPQ’s conclusion, its contribution to fungal allergies is likely low. No specific allergenic fraction is listed with the FDA’s Biological Product registry or the International Union of Immunological Societies; the one commercial allergen preparation still trades under the old name, Cephalosporium acremonium. One cited study found sensitivity in 16 percent of 101 patients with allergic bronchial asthma — a clinic population, printed as such.
- Hypersensitivity pneumonitis. Type III hypersensitivity pneumonitis due to Acremonium has been reported in a few instances, mostly associated with contaminated home humidifiers — including a study of five patients with HP from contaminated home ultrasonic humidifiers, all testing strongly positive for precipitins against the humidifier water and against Cephalosporium acremonium extract, and a further case presumptively tied to sewage flooding. The humidifier is this genus’s recurring exposure machine in the agency record: a reservoir of treated water, aerosolised into a room.
- Infections — infrequent, split by host. The INSPQ calls Acremonium species infrequent pathogens in humans that can cause a spectrum from mycotic keratitis and mycetoma in the normal host to fungemia, disseminated infection, and cutaneous infection in immunocompromised subjects. About ten species are reported as causes of infection, A. kiliense the most important. The normal-host route is traumatic penetration — soil-borne inoculation through a wound, presenting most commonly as foot mycetoma or corneal infection after penetrating injury, with contact-lens and post-keratitis keratomycosis also reported; ocular infections are the second most common Acremonium disease in the sheet. The immunocompromised record is graver and is printed at its published weight: invasive and disseminated infections are almost exclusively observed in immunocompromised patients (transplant recipients, myeloma and leukemia patients, patients on corticoid therapy), the lungs and gastrointestinal tract the apparent portals, the clinical list running from sinusitis and osteomyelitis to pneumonia, peritonitis, endocarditis, and cerebritis — and among neutropenic patients with disseminated infection, about half died. A genus that does not grow at body temperature in most species, and still kills through the species and circumstances that get past that limit: the record is rare, and the record is real, and the INSPQ prints both.
- The hospital record. True nosocomial transmission has rarely been reported, yet the INSPQ carries the sheet’s most striking institutional sentence: an outbreak of A. kiliense endophthalmitis after cataract surgery in an ambulatory surgical centre, whose reservoir was determined to be a contaminated humidifier within the HVAC system located directly above the operating suite. A wet machine over a sterile room, again. The sheet also records isolation from surgical-instrument rinse water and from hospital air filters — in the filter study, in only one of seven hospitals, and explicitly not as a major fungal contaminant next to Aspergillus, Cladosporium, or Alternaria. No occupational infections have been reported for specific occupations.
- The CDC’s general frame, for scale. The US CDC publishes that exposure to damp and moldy environments may cause a variety of health effects or none at all; that for some people mold can cause a stuffy nose, sore throat, coughing or wheezing, burning eyes, or skin rash; that people with asthma or mold allergy may have more severe reactions; and that immune-compromised people may get lung infections from mold. The CDC does not publish an Acremonium species sheet; its frame is the general one, and this brief does not promote it into a species finding.
Mycotoxins — the livestock record, fenced
Many strains of Acremonium are active producers of toxins under given growth conditions, and the INSPQ’s toxic-effects column is an animal column: cytotoxic, nephrotoxic, and tremorgenic effects, well documented in livestock — Acremonium-infected tall fescue behind fescue toxicosis in cattle and horses, ryegrass staggers with its tremorgen lolitrem-B, high morbidity in grazing herds. And then the sentence this page exists, in part, to print exactly: no cases of human mycotoxicosis have yet been reported. The standing discipline of Mold Toxicity and Mycotoxins applies in its cleanest form: a genus can carry a genuine agricultural toxin record and an indoor inhalation record of none reported at the same time, and a page that merges the two into an indoor toxin scare has left its sources. The indoor record above — allergy at low prevalence, humidifier HP, trauma and opportunist infection — is the whole of what the agency publishes for buildings.
Found together with
- Stachybotrys chartarum — the INSPQ’s own pairing: Acremonium is often seen growing in combination with Stachybotrys and often reported associated with Stachybotrys contamination, both favoured by very wet circumstances. A sample naming one is, on the agency’s record, a reason to look for the other — same water, same materials.
- Fusarium — the diagnostic twin: the INSPQ records that Fusarium and Acremonium cannot be distinguished by histopathological examination alone, and their mycetoma grains are near-identical — a laboratory’s genus-level caution, printed here because a tissue report naming either has a named look-alike.
Found in gyms
No Gym Watch location page currently names Acremonium from a location-specific test. The habitat record is the gym sentence: this genus’s published indoor homes are cooling coils, drain pans, humidifier water, and HVAC fibreglass insulation — the wet machinery that serves every locker room and pool hall on this site, and the machinery least visible to the members breathing under it. When a location test names Acremonium, it will be linked here; this list is built from records, not assumptions. Until then the brief’s use is the water-activity number: Aw 0.90–0.98 is a soaked material, not a damp one — a report naming this genus is a report that something in the building stayed very wet for a long time.
How it is tested and documented
Building side: the genus’s slime-bound spores mean air sampling understates it — the INSPQ prints the limited aerosolisation as a property of the organism — so the honest building record pairs air sampling with material and surface sampling of the wettest components themselves: coil, drain pan, humidifier reservoir, duct liner, crawl-space materials, photographed and dated, with the moisture reading that explains them (the Finnish crawl-space link was established exactly that way). Field method: How to Test a Sauna. Laboratory side: the INSPQ warns that Acremonium species are ubiquitous and often considered laboratory contaminants — which cuts both ways, and the sheet knows it: because hyalohyphomycosis is seldom considered on primary culture, a positive culture from a deep site should be verified rather than dismissed, with cultures required to complete a diagnosis that histopathology can only open (its grains and hyphae imitate Fusarium). Immunodiagnosis trades under the old name: the available Cephalosporium acremonium allergen (FDA listing GJ30) serves IgE skin and RAST testing; precipitin testing remains experimental. Diagnosis and treatment belong to clinicians.
Tools for this job: Test — find out what is actually there
GOT MOLD?
Fit score 10/10 — our research rating of how well this program fits this site's readers
What it is: A do-it-yourself mold test kit with the laboratory analysis included — the kit price covers the lab fees and free two-way shipping, per the program's own page.
Why it is listed: It is the exact purchase a reader of this site is already looking for: sample it yourself, mail it in, get a lab identification back. The all-in pricing matters — no surprise lab bill after the swab.
Its limits: Like every surface kit, it identifies what is present where you sampled. It does not count airborne spores, measure a dose, or prove that a room caused an illness.
My Mold Detective
Fit score 9/10 — our research rating of how well this program fits this site's readers
What it is: A recognised do-it-yourself mold test kit brand with lab analysis of your samples.
Why it is listed: An established name readers encounter everywhere in this space, with an easy sampling process a first-timer can follow — a reasonable starting point for a documented record.
Its limits: Same class limits as any consumer kit: presence and identification at the sampled spots, not air concentration, not causation.
EnviroBiomics — ERMI & HERTSMI-2
Fit score 10/10 — our research rating of how well this program fits this site's readers
What it is: Laboratory dust analysis by PCR. You collect a settled-dust sample and the lab reports mold species DNA: the ERMI panel, and the narrower HERTSMI-2 score built from five species associated with water-damaged buildings.
Why it is listed: This is the reference dust test that mold-literate readers ask for by name — the one that appears throughout the serious literature and community documentation on water-damaged buildings.
Its limits: Dust is history, not a live exposure reading: it says what has settled over time, not what you are breathing today. The EPA developed ERMI as a research tool and has not validated it for routine home decision-making — treat scores as one documented input, not a verdict.
The Dust Test
Fit score 9/10 — our research rating of how well this program fits this site's readers
What it is: Mail-in dust PCR analysis covering 36 mold species, with an explanation-friendly report format.
Why it is listed: A premium, content-friendly test: the species-level report gives a household (and any professional they hand it to) something concrete to work from.
Its limits: Same dust-history caveat as every PCR dust test — settled dust over time, not today's air. The program's stated audience is practitioners and wellness professionals.
Ulta Lab Tests — mold allergy panels
Fit score 7/10 — our research rating of how well this program fits this site's readers
What it is: Direct-to-consumer laboratory testing for people — including mold allergy panels — that you order yourself without a doctor's visit first.
Why it is listed: Listed separately and deliberately: everything above tests the *building*; this tests *you*. Readers who were told 'it's just allergies' can put an actual lab result next to that claim.
Its limits: This is medical testing, and this site gives no medical advice. A panel result is information to take to a clinician — ideally one experienced with environmental illness — not a diagnosis and not proof of where an exposure happened.
Some links in this strip are affiliate links and cost you nothing extra if you buy through one. As an Amazon Associate I earn from qualifying purchases. Affiliate money never buys scores, coverage, or silence — see our affiliate disclosure.
Sources
- INSPQ (Institut national de santé publique du Québec), Acremonium spp. fact sheet (Mould Compendium) — inspq.qc.ca/en/moulds/fact-sheets/acremonium-spp
- US CDC, Mold (general mold framing; CDC publishes no Acremonium species sheet) — cdc.gov/mold-health/about
If this happened to you
Found mold — growth at a cooling coil, a drain pan, a humidifier, a crawl-space joist — in a gym, a rental, a school, or a workplace and nobody with authority would act? Put it on the record. A dated public report is the tripwire that, in most of the United States, does not otherwise exist.